Installation of Concreate

Installation of Concreate

Flooring Installation Guide


Before goods are delivered to site - Before Concreate flooring can be delivered to site all wet trades (e.g. concreting, plastering, and decorating) must be finished, and the building must be weather tight and thoroughly dried out. (Please note that plaster may take several months to dry satisfactorily, concrete and screeds may take substantially longer depending on thickness. The relative humidity must be in the range 45-65%, with ambient temperature in the range of 18°C to 24°C. If necessary, employ a dehumidifier to maintain suitable conditions.




Acclimatization of Concreate Flooring - As part of your warrantee conditions, it is essential to acclimatize your Concreate Flooring prior to installation. Providing that site conditions are correct before the panels arrive, the panels should be stored in packs prior to laying in warm dry conditions (i.e. similar to those which will prevail when the floor is laid and in use: 45 to 65% RH). The panels should be stored in the room(s) where they are to be laid for a minimum of three days, to allow them to acclimatize to the ambient temperature and humidity. The flooring must be well protected against damage or marking from other building operations. It is recommended that the panels are kept in the packaging until installation commences.

Installation basics - Concreate must be installed by fully bonding to suitable sub-floors or to Concreate approved 3mm underlay using Concreate Flooring Adhesive and Concreate Flooring Adhesive notched trowel. Concreat should be cut with the appropriate fully extracted diamond tipped saw blade. Concreate Flooring may be used over under-floor heating.


Provision for expansion - Although it is very unlikely that Concreate will move it is recommended that expansion spaces of 5mm or more must be left wherever the floor meets obstructions including all walls, doorframes, thresholds, structural support, fireplaces etc. These expansion gaps can be covered using flexible mastic.

Fitting Pattern - Concreate panels may be installed random or geometric patterns. The diagrams below show some patterns the grey rectangles indicate the cement panels and the brown rectangles the wooden top layer panels.


Important - Concreate is a natural surface with tonal and colour variation. To achieve the desired mix of colours, shades and other characteristics in the final floor, and avoid clusters of similar colour shades, the contents of multiple packs should be mixed during installation. Samples must be taken as a guide only and colour/shade and other characteristics will vary. Before installation commences rack out a small section of boards for the client approval. This product may include up to 3-5% of boards which do not meet the usual tolerances or grade, which should be defect cut or set aside as waste.


The installer is the last line of quality control.
DO NOT INSTALL BOARDS WITH OBVIOUS DEFECTS - Concreate must be handled with care and the packs must be opened carefully to avoid damaging the edges and the tongue and groove system. Avoid fitting damaged panels. Minor damages such as chips may be repaired once installed with Concreate repair powder.

Condition of sub-floors - All sub-floors must be dry, sound and of load-bearing strength. It is essential that wood based sub-floors must be of load bearing strength (e.g. Typically 22mm thickness on joist or battens at 600mm centres 18mm thickness if on joists of 400mm centres) and free from excessive deflection under loading.


Moisture condition of sub-floors - Concrete slabs and sand-cement screeds must be sound, and dry. Mineral based sub-floors must not exceed 75% equilibrium relative humidity or <0.3% Moisture content for anhydrite. Sub-floors at ground level or below must contain an effective damp proof membrane to protect flooring from ground water in compliance with British Standards. If there is any doubt that the sub-floor meets the required standard for moisture or the sub-floor does not have an effective integral damp proof membrane, a suitable surface applied damp proof membrane must be installed.

Wooden sub-floors must not be more than 2% higher in moisture than the Concreate (wood) Flooring. When installing wood flooring at ground floor level (or below) above a ventilated cavity (e.g. floorboards suspended on joist), it is essential that a purpose made moisture barrier building paper is installed over the sub-sub-floor before flooring can be installed. The moisture barrier must taken up the walls by 30mm at the perimeter, and all joins overlapped by a minimum 200mm and taped with a water proof jointing tape. Failure to comply with requirements for sub-floor moisture may result in cupping and excessive expansion of the Concreate Wood Panel which is not covered by the warrantee.

Evenness of sub-floors - The maximum permissible departure from the underside of a 2 lineal meter straight edge is 2mm. Failure to keep to these tolerances may result in deflection which may produce undue stresses on the joints, cause gaps between flooring elements, and with fully bonded floors may result in inadequate contact between flooring and adhesive.

If levelling is required over sand-cement screed or concrete sub-floors it is recommended that a rapid curing high strength water-powder mix cementitious levelling compound is employed instead of a powder + liquid latex emulsion. If levelling wood based sub-floors prior to fully bonding wood flooring, a purpose made fibre reinforced levelling compound must be used. Ensure that levelling compounds are fully cured and thoroughly dried before installation commences.

In some cases such as over suspended floorboards, levelling may be achieved by overlaying the existing sub-floor with a sheet material such as WBP grade Plywood or OSB chipboard. The sheet material must be securely fixed to the wood based sub-floor with the ends of sheet staggered. Ensure adequate provision for expansion between sheets of plywood using washer joints.

If levelling is required above an epoxy resin surface moisture barrier, it is recommended that an additional application of epoxy is applied and a purpose made aggregate is applied onto the freshly applied epoxy. Once the epoxy is fully cured any aggregate which is not fully adhered to the epoxy is vacuumed off. This produces a sandpaper like surface which provides a strong mechanical key between epoxy membrane and levelling compound. Always check the mutual compatibility of moisture barriers, primers, aggregates, levelling compounds and adhesives before installation. See manufacturer’s product data sheet for further information.

woods_good_ms_plus_concreate_and_wood_flooring_adhesiveFully bonded installation(eg. Concrete, sand-cement screed or wood based sub-floors) with Wood's Good MS Plus Concreate Flooring Adhesive - Concreate Flooring may be installed direct to concrete or sand-cement screed sub-floors, or to suitable wood based sub-floors (e.g. Plywood, OSB) by fully-bonding with a purpose made permanently flexible Concreate Flooring Adhesive. Concrete subfloors must be < 65% relative humidity.

The adhesive is applied to the sub-floor only using the Concreate trowel, which creates ridges of adhesive which the flooring is bedded into when laid. Always use the Concreate trowel and replace trowels which are worn.

Tip: When installing flooring uplift occasional panels after placement and examine the residues of adhesive on the underside of the panel to ensue the panel is making full with the bed of adhesive.

Important notes - Previous floor coverings and the adhesive residues used to adhere floor coverings to sub-floors (e.g. Bitumen) must be removed before bonding of wood flooring.

Ensure screeds are of adequate cohesion strength of before installation.

Avoid accelerated drying of new screeds as this can lead to poor cohesive strength, especially over under floor heating.

Any residues of adhesive which come into contact with the face of the board must be removed whilst wet, as cured residues are not easily removable.

Disclaimer & further information - The combination and order of products used for sub-floor preparation can vary according to specific conditions of the site and sub-floor. This information is not intended to be exhaustive, or a how to guide for the novice, but will serve as a guide only to the experienced installer. Further information is available